CL1212E Industrial CopperLink Ultra High-Speed Copper Ethernet Extender 168 Mbps

- Ethernet Extension Extend 10/100Base-TX Ethernet well beyond its 328-foot (100-meter) limitation over a single unshielded twisted pair (UTP) or Cat 5e/ Cat 6 or Cat 7 cable.

- Operates Over Twisted Pair Realise fibre-optic speeds without the expense and hassle of installing new cables or line-of-site wireless circuits.

- Plug and Play Set these units up straight out of the box. No configuration is required. Dual auto-sensing 10/100 Ethernet ports support full or half duplex operation. 

- Multiple Line Rates Supported Switch-selectable rate mode options optimise rate and reach for the noise environment, wire gauge/type and length.

- Transparent LAN Bridging Bypass network configuration requirements by transparently passing all higher layer protocols—including 802.1Q VLAN frames (tagged and untagged).

- Made in the USA The Patton CopperLink  CL1212E is designed by Patton engineers and built in Patton's Gaithersburg, Maryland facility. Patton's American-made manufacturing process delivers high-quality networking solutions with reliability you can trust.

CopperLink Line Interface

- RJ-45 (pin 4 = ring; pin 5 = tip)

- Terminal block, 2 position

- BNC 75-ohm Coax

CopperLink Line Modulation

- DMT (Discrete Multi-Tone) 

Ethernet Interface (x2)

- 8-position, shielded RJ-45. Auto-sensing 10/100Base-TX with half or full duplex operation.

Protocol

- Transparent to high layer protocols: supports 802.1Q VLAN tagged or untagged frames.

- Transparent to IP Video schemes: fully transparent to such compression schemes as MPEG-4, H.264, and MJPEG. 

Target SNR Modes

-   6 dB and 9 dB 

Management

- 8-position DIP switch 

Monitoring

-6 LEDs display status for the following:

- Pwr (Power)

- Line

- Eth (Ethernet) 0 & Eth 1

- R (Remote)

- L (Local)

Power Supply

- External AC: 100–240 VAC 

Compliance

- FCC Part 15A, CE Mark, EMC Directive 89/336/EEC, Low-Voltage Directive 73/23/EEC 

Environment

- Extended Temperature: -40 to 85°C 

- Extended Humidity: 5 to 85%, condensing

Dimensions

- 30.2 W x 108.7 H x 85.3 D mm

Weight

- 623.7 g

MTBF

- 77,000 hours 

CL1212E/EUI Industrial Extended Temperature High Speed CopperLink Ethernet Extender; 2 x 10/100BaseTX; RJ45 Line, 100-240VAC

* Single unit for use as Transmitter (Local) or Receiver (Remote) and PSU

CL1212E/EUI-2PK  Industrial Extended Temperature High Speed CopperLink Ethernet Extender Kit (Local and Remote); 2 x 10/100BaseTX; RJ45 Line, 100-240VAC

* Includes Transmitter (Local) and Receiver (Remote) and PSUs

CL1212E/TB/EUI Industrial Extended Temperature High Speed CopperLink Ethernet Extender; 2 x 10/100BaseTX; Terminal Block Line, 100-240VAC

* Single unit for use as Transmitter (Local) or Receiver (Remote) and PSU

CL1212E/TB/EUI-2PK Industrial Extended Temperature High Speed CopperLink Ethernet Extender Kit (Local and Remote); 2 x 10/100BaseTX; Terminal Block Line, 100-240VAC

* Includes Transmitter (Local) and Receiver (Remote) and PSUs

CL1212E/CC/EUI Industrial Extended Temperature CopperLink High Speed Auto Rate Extender; 2 x 10/100BaseTX; RJ45 Line Connector; Conformal Coated; 100-240VAC

* Single unit for use as Transmitter (Local) or Receiver (Remote) and PSU

CL1212E/CC/EUI-2PK Industrial Extended Temperature CopperLink High Speed Auto Rate Extender Kit; 2 x 10/100BaseTX; RJ45 Line Connector; Conformal Coated; 100-240VAC

* Includes Transmitter (Local) and Receiver (Remote) and PSUs

CL1212E/TB/CC/EUI Industrial Extended Temperature CopperLink High Speed Auto Rate Extender; 2 x 10/100BaseTX; Terminal Block Line Connector; Conformal Coated; 100-240VAC

* Single unit for use as Transmitter (Local) or Receiver (Remote) and PSU

CL1212E-SKD Ethernet Extender, PCB Sub Assembly, RJ45 Line; 2 x 10/100; No Power Supply 

CL1212E/TB-SKD Ethernet Extender, PCB Sub Assembly, Terminal Block Line; 2 x 10/100; No Power Supply